ElektraLite MY 250 Instrukcja Użytkownika

MY 250 USER MANUAL (V1.12) Elektralite is a division of Group One. 70, Sea Lane, Farmingdale, NY 11735, USA. Tel: +1 (516)-249-3662. Fax: +1 (516

9 The display panel. The display panel on MY 250 offers many features. For example, you can set the starting address, switch on and off the lamp, run

10 Main functions - Main menu 0 1. Press [ENTER] for 3 seconds to enter the main menu "MODE" (display flashing) 2. Press [ENTER] and sel

11 1. Select "AUTO" or "SOUN" by pressing [UP]. 2. Press [ENTER] for selecting the desired extension menu. 3. Select "ALON

12 1. Press [ENTER] for 3 seconds to enter the main menu (display flashing). 2. Press [UP] to select “LAMP”. - Lamp on/off This function switches t

13 - Tilt Reverse This function reverses the Tilt movement. 1. Select “rTIL” by pressing [UP] button. 2. Press [ENTER], the display shows “ON” or “O

14 adjusted. In this mode, the device will not react to any control signal. 1. Select “LADJ” by pressing [UP] button. 2. Press [ENTER], the display s

15 1. Select “CLLT” by pressing [UP] button. 2. Press [ENTER], the display shows “ON” or “OFF”. 3. Press [UP] to select “ON” to enable this function

16 Call up the first scene in your controller now. 1. Select “SC01” by pressing [UP] button. 2. Press [ENTER], the display shows “SC01”. 3. Press [EN

17 INSTRUCTIONS ON USE: The moving head is controlled by 14 DMX channels CHANNEL 1 : select one of the 9 colors, color cycle or rainb

18 DMX channel’s function and values: Channel 1 – Color Wheel: 0-13 Open / white 14-27 Orange 28-41 Blue 42-55 Green 56-69 Yellow 70-83 Red 84-97 M

1 Introduction Thank you for choosing Elektralite’s MY 250 fixture. Please read the User Manual carefully and keep it in a safe place after reading i

19 Channel 3 – Rotation gobo index , rotating gobo 0-127 Gobo indexing 128-187 Forward gobo rotation from fast to slow 188-191 No rotation 192-255

20 Channel 8 –3 facet rotating prism, Prism / Gobo macros 0-3 open 4-63 Forwards rotation from fast to slow 64-67 No rotation 68-127 Backwards rota

21 Channel 12 – Lamp on/off, reset, internal 0-19 color change normal by direction depend on distance 20-39 color change to any position by directi

22 06Er: Tilt head movement error. This message will appear after resetting MY 250 and the head’s magnetic-indexing circuit malfunctions (sensor f

23 Other Elektralite Products include : [Also check out our website at www.myelektralite.com] CP-3 Controller. CP-10xt Controller. CP-16 /24 Co

24 CP-20xt Controller. TurboFog + Fog Machine.

2 Make sure that the power is only 120 volts. This unit will be damaged if you chose to install it at any other voltage. In an installation it is alw

3 GENERAL GUIDELINES MY 250 is a lighting effect for professional use on stages, in clubs, theatres, and so on. This fixture should only be operat

4 for a special wipe to clean the lamp. 4. Only install Philips MSD 250 or MSD 250/2 GY9.5 lamp. Any other lamp is not acceptable. Procedure: 1.

5 . Safety-chainM10 X 25m m Using M10 (10mm) bolts screw the C clamps onto the base of MY 250 make sure that the bolts are firmly tightened but take

6 Method 2 : Installation using U Bracket Claps with half Cheeseboros/couplers. [The U brackets and the appropriate base for the mounting these brac

7 DMX has a maximum running distance of 330 feet. When long distances are involved then there is a tendency for electrical noise to be evident. In

8 Projector DMX start address selection In order for the controller like Elektralite’s CP10xt to control each MY 250 it has to know where it is in t